192 photomicrosensor (transmissive) EE-SX199 photomicrosensor (transmissive) EE-SX199 dimensions note: all units are in millimeters unless otherwise indicated. features ? general-purpose model with a 3-mm-wide slot. pcb mounting type. high resolution with a 0.5-mm-wide aperture. with a positioning boss. rohs compliant. absolute maximum ratings (ta = 25 c) note: 1. refer to the temperature rating chart if the ambient temper- ature exceeds 25 c. 2. the pulse width is 10 s maximum with a frequency of 100 hz. 3. complete soldering within 10 seconds. ordering information electrical and optical characteristics (ta = 25 c) internal circuit k a c e terminal no. name a anode k cathode c collector e emitter four, 0.5 0.1 four, 0.25 0.1 tw o, c 1 0.3 four, c0.3 tw o, 0 . 7 0 -0.1 dia. optical axis cross section bb cross section aa c e k a 6.5 0.1 6.2 0.5 10 0.2 12.2 0.3 9.2 0.3 8.5 0.1 0.5 0.1 5 0.1 2.5 0.1 4.3 unless otherwise specified, the tolerances are 0.2 mm. item symbol rated value emitter forward current i f 50 ma (see note 1) pulse forward current i fp 1 a (see note 2) reverse voltage v r 4 v detector collector?emitter voltage v ceo 30 v emitter?collector voltage v eco --- collector current i c 20 ma collector dissipation p c 100 mw (see note 1) ambient temperature operating topr ?25 c to 85 c storage tstg ?40 c to 100 c soldering temperature tsol 260 c (see note 3) description model photomicrosensor (transmissive) EE-SX199 item symbol value condition emitter forward voltage v f 1.2 v typ., 1.4 v max. i f = 30 ma reverse current i r 0.01 a typ., 10 a max. v r = 4 v peak emission wavelength p 940 nm typ. i f = 20 ma detector light current i l 0.5 ma min., 14 ma max. i f = 20 ma, v ce = 5 v dark current i d 2 na typ., 200 na max. v ce = 20 v, 0 l x leakage current i leak --- --- collector?emitter saturated voltage v ce (sat) 0.1 v typ., 0.4 v max. i f = 40 ma, i l = 0.5 ma peak spectral sensitivity wavelength p 850 nm typ. v ce = 10 v rising time tr 4 s typ. v cc = 5 v, r l = 100 ? , i l = 5 ma falling time tf 4 s typ. v cc = 5 v, r l = 100 ? , i l = 5 ma
photomicrosensor (transmissive) EE-SX199 193 engineering data forward current vs. collector dissipation temperature rating forward current vs. forward voltage characteristics (typical) light current vs. forward current characteristics (typical) light current vs. collector ? emitter voltage characteristics (typical) dark current vs. ambient temperature characteristics (typical) distance d (mm) input output input output 90 % 10 % (center of optical axis) sensing position characteristics (typical) response time measurement circuit ambient temperature ta ( c) collector dissipation p c (mw) forward voltage v f (v) forward current i f (ma) forward current i f (ma) forward current i f (ma) light current i l (ma) collector ? emitter voltage v ce (v) light current i l (ma) ambient temperature ta ( c) load resistance r l (k ? ) ta = ? 30 c ta = 25 c ta = 70 c ta = 25 c v ce = 5 v i f = 40 ma i f = 30 ma i f = 20 ma i f = 10 ma ta = 25 c v ce = 10 v 0 l x i f = 20 ma v ce = 5 v i f = 20 ma v ce = 10 v ta = 25 c v cc = 5 v ta = 25 c response time tr, tf ( s) relative light current i l (%) dark current i d (na) relative light current i l (%) i f = 50 ma ambient temperature ta ( c) i f p c relative light current vs. ambi- ent temperature characteristics (typical) response time vs. load resist- ance characteristics (typical)
terms and conditions of sale 1. offer; acceptance . these terms and conditions (these "terms") are deemed part of all quotations, acknowledgments, invoices, purchase orders and other documents, whether electronic or in writi ng, relating to the sale of products or services (collectively, the "products") by omron electronic components llc ("seller"). seller hereby objects to any terms or conditions proposed in buyer's purchase order or other document s which are inconsis tent with, or in addition to, these terms. 2. prices; payment . all prices stated are current, subject to change without notice by seller. buyer agrees to pay the price in effect at time of shipment. payments for products received are due net 30 days unless otherwise stated in the invoice. 3. discounts . cash discounts, if any, will apply only on the net amount of invoices sent to buyer after deducting transportation charges, taxes and duties, and will be allowed only if (i) the invoice is paid according to seller's payment terms and (ii) buyer has no past due amounts owing to seller. 4. currencies . if the prices quoted herein are in a currency other than u.s. dol- lars, buyer shall make remittance to seller at the then current exchange rate most favorable to seller and which is available on the due date; provided that if remittance is not made when due, buyer will convert the amount to u.s. dol- lars at the then current exchange rate most favorable to seller available during the period between the due date and the date remittance is actually made. 5. governmental approvals . buyer shall be responsible for, and shall bear all costs involved in, obtaining any government approvals required for the impor- tation or sale of the products. 6. taxes . all taxes, duties and other governmental charges (other than general real property and income taxes), including any interest or penalties thereon, imposed directly or indirectly on seller or required to be collected directly or indirectly by seller for the manufacture, production, sale, delivery, importation, consumption or use of th e products sold hereunder (including customs duties and sales, excise, use, turnover and license taxes) shall be charged to and remitted by buyer to seller. 7. financial . if the financial position of buyer at any time becomes unsatisfactory to seller, seller reserves the right to stop shipments or require satisfactory security or payment in advance. if buyer fails to make payment or otherwise comply with these terms or any related agreement, seller may (without liability and in addition to other remedies) cancel any unshipped portion of products sold hereunder and stop any products in transit until buyer pays all amounts, including amounts payable hereunder, whether or not then due, which are owing to it by buyer. buyer shall in any event remain liable for all unpaid accounts. 8. cancellation; etc . orders are not subject to rescheduling or cancellation unless buyer indemnifies seller fully against all costs or expenses arising in connection therewith. 9. force majeure . seller shall not be liable for any delay or failure in delivery resulting from causes beyond its control, including earthquakes, fires, floods, strikes or other labor disputes, short age of labor or materials, accidents to machinery, acts of sabotage, riots, delay in or lack of transportation or the requirements of any government authority. 10. shipping; delivery . unless otherwise expressly agreed in writing by seller: 1. shipments shall be by a carrier selected by seller; 2. such carrier shall act as the agent of buyer and delivery to such carrier shall constitute delivery to buyer; 3. all sales and shipments of products shall be fob shipping point (unless otherwise stated in writing by seller), at which point title to and all risk of loss of the products shall pass from se ller to buyer, provided that seller shall retain a security interest in the products until the full purchase price is paid by buyer; 4. delivery and shipping dates are estimates only. 5. seller will package pr oducts as it deems proper for protection against normal handling and extra charges apply to special conditions. 11. claims . any claim by buyer against seller for shortage or damage to the products occurring before delivery to t he carrier must be presented in writing to seller within 30 days of receipt of shipment and include the original trans- portation bill signed by the carrier noting that the carrier received the products from seller in the condition claimed. 12. warranties . (a) exclusive warranty . seller's exclusive warranty is that th e products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by seller (or such other period expresse d in writing by seller). seller disclaims all other warranties, express or implie d. (b) limitations . seller makes no warranty or representatio n, express or implied, about non-infringement, merchantabi l- ity or fitness for a particular purpose of the product s. buyer acknowledges that it alone has determined that th e products will suitably meet the requirements of the ir intended use. seller further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the products or ot h- erwise of any intellectual property right. (c) buyer remedy . seller's sole ob li- gation hereunder shall be to replace (in the form originally shipped with buy er responsible for labor charges for re moval or replacement thereof) the no n- complying product or, at seller's election, to repay or credit buyer an amou nt equal to the purchase price of the product; provided that in no event sh all seller be responsible for warranty, r epair, indemnity or any other claims or expenses regarding the produc ts unless seller's analys is confirms that th e products were properly handled, stored, installed and maintained and not su b- ject to contamination, abuse, misuse or inappropriate modification. return of any products by buyer must be approved in writing by seller before shipmen t. seller shall not be liable for the suitability or unsuitability or the results from th e use of products in combination with any electrical or electronic component s, circuits, system assemblies , or any other materials or substances or enviro n- ments. any advice, recommendations or information given orally or in writin g are not to be construed as an amendment or addition to the above warranty. 13. limitation on liability; etc . seller shall not be liable for specia l, indirect, incidental or consequential damages, loss o f profits or production or commercial loss in any way con - nected with the products, whether such claim is based in contract, warranty, negligence or strict liability. further, in no event shall liability of seller ex ceed the individual price of the product o n which liability is asserted. 14. indemnities . buyer shall indemnify and hold harmless seller, its affiliates an d its employees from and against all liabilities, losses, claims, costs an d expenses (including attorney's fees and expenses) related to any claim, inve s- tigation, litigation or proceeding (whether or not seller is a party) which arise s or is alleged to arise from buyer's ac ts or omissions under these terms or in any way with respect to the products. without limiting the foregoing, buyer ( at its own expense) shall indemnify and hold harmless seller and defend or sett le any action brought against seller to the extent that it is based on a claim th at any product made to buyer specifications infringed intellectual property righ ts of another party. 15. property; confidentiality . the intellectual property embodied in the products is the exclusive property of seller and its affiliates and buyer shall not attempt to duplicate it in any way without the written permission of seller. notwithstan d- ing any charges to buyer for engineering or tooling, all engineering and toolin g shall remain the exclusive property of seller. all information and materials su p- plied by seller to buyer relating to the products are confidential and prop ri- etary, and buyer shall limit distribution thereof to its trusted employees an d strictly prevent disclosure to any third party. 16. miscellaneous . (a) waiver . no failure or delay by seller in exercising any rig ht and no course of dealing between buyer and seller shall operate as a waiv er of rights by seller. (b) assignment . buyer may not assign its rights hereund er without seller's written consent. (c) law . these terms are governed by i lli- nois law (without regard to conflict of law principles). federal and state cour ts in illinois shall have exclusive jurisdiction for any dispute hereunde r. (d) amendment . these terms constitute the entire agreement between buy er and seller relating to the products, and no provision may be changed or waived unless in writing signed by the parties. (e) severability . if any provisio n hereof is rendered ineffective or invalid, such provision shall not invalidate an y other provision. (f) setoff . buyer shall have no right to set off any amoun ts against the amount owing in respect of this invoice.. (g) definitions . as use d herein, "including" means "including without limitation".
certain precautions on specifications and use 1. suitability for use . seller shall not be responsible for conformity with any stan- dards, codes or regulations which appl y to the combination of the product in buyer's application or use of the product. at buyer's request, seller will pro- vide applicable third party certification documents identifying ratings and limita- tions of use which apply to the product. this information by itself is not sufficient for a complete determination of the suitability of the product in combi- nation with the end product, machine, system, or other application or use. buyer shall be solely responsible for determining appropriateness of the partic- ular product with respect to buyer's application, product or system. buyer shall take application responsibility in all cases but the following is a non- exhaustive list of applications for which particular attention must be given: (i) outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or us es not described in this document. (ii) energy control systems, combusti on systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. (iii)use in consumer products or any use in significant quantities. (iv)systems, machines and equipment that could present a risk to life or property. please know and observe all pr ohibitions of use applicable to this product. never use the product for an application involving serious risk to life or property without ensuring that the system as a whole has been designed to address the risks, and that the omron product is properly rated and installed for the intended use within the overall equipment or system. 2. programmable products . seller shall not be responsible for the user's programming of a programmable product, or any c onsequence thereof. 3. performance data . performance data given in this publication is provided a s a guide for the user in determining suit ability and does not constitute a warran ty. it may represent the result of seller's test conditions, and the users must cor re- late it to actual application requirem ents. actual performance is subject to seller's warranty and limitations of liability. 4. change in specifications . product specifications and accessories may be changed at any time based on improvements and other reasons. it is our pra c- tice to change part numbers when published ratings or features are change d, or when significant construction changes are made. however, some specific a- tions of the product may be changed without any notice. when in doubt, sp e- cial part numbers may be assigned to fix or establish key specifications for yo ur application. please consult with your se ller representative at any time to co n- firm actual specificat ions of purchased product. 5. errors and omissions . the information in this publication has been carefu lly checked and is believed to be accurate; however, no responsibility is assum ed for clerical, typographical or proofreading errors, or omissions. 6. rohs compliance . where indicated, our products currently comply, to the b est of our knowledge as of the date of this publication, with the requirements of t he european union's directive on the restriction of certain hazardous su b- stances ("rohs"), although the requirements of rohs do not take effect u ntil july 2006. these requirements may be subject to change . please consult o ur website for current information. omron on-line global - http://www.omron.com usa - http://www.components.omron.com canada - http://www.omron.ca cat. no. jb301-e3-01 printed in usa omron canada, inc. 885 milner avenue toronto, ontario m1b 5v8 416-286-6465 omron electronic components llc 55 e. commerce drive, suite b schaumburg, il 60173 847-882-2288 3/05 specificat ions subject to change without notice complete ?terms and conditions of sale? for product purchase and use are on omron?s website at www.components.omron.com ? under the ?about us? tab, in the legal matters section. all dimensions shown are in millimeters. to convert millimeters into inches, multiply by 0.0393 7. to convert grams into ounces, multiply by 0.03527.
|
